Items in Basket Amount |
0
0,00 €
|
---|
PINI P Towel Radiator 608x776mm, 456W, white
Description
Properties
Brand | SAPHO | |
---|---|---|
Series | PINI | |
Size | 608x776 mm | |
Width | 608 mm | |
Height | 776 mm | |
Colour | White | |
Material | Steel | |
Shape | H-Shape | |
Suggested el. heater | 300 W | |
Possibility of heating | Electric Heating, Combined heating - Electric/Central, Central heating | |
Spacing connection | 558 mm | |
Output | 456 W | |
Weight / Piece | 9.06 kg | |
Packing | 1 Piece | |
Guarantee | 2 years |
Explanations
Electric heating
If the heater is only heated electrically, i.e. only a heating rod is used, a 1/2" radiator plug must be purchased additionaly. This serves to plug the other hole in the heater which would otherwise be used for the central heating connection valve. We recommend filling the heater with distilled water. It is also recommended to pour in the LIKIDO antifreeze and anti-corrosive heat transfer fluid.
It is necessary to use a heating rod with the same or similar performance according to the specification of the radiator. For heating rods with a thermostat, the temperature of the liquid in the heater is controlled.
Dual fuel heating
Dual fuel towel rails combine two types of heating - central and electric. They can be connected to the central heating system, and also to an electric socket. We recommend a heating rod with the same or similar performance according to the specification of the radiator.
If you have a heater with a central connection, in depends on whether the heating rod can be connected via a valve (in such case a combination valve is used) or whether the rod is connected separately to the side part of the radiator (using a conventional valve). In case of a side connection, a combination valve is always used. There is a choice of using a manual valve or a valve with a thermostatic head
Manual valve: the valve control head can be installed on the left/right side regardless of the hot water supply location. The temperatur eis controlled manually.
A valve with a thermostatic head: the integrated thermostat maintains the temperature inside the towel rail. The thermostatic head must be located at the hot water inlet (except MONO ONE).
The connection valves we offer are supplied with a clamping fitting for the most common pipes (Ø15 mm for copper and Ø16 mm for Alupex), so there is no need to buy anything else for the connection. For covering the inlet pipes and holes in the wall, we recommend the addition of cover rosettes.
Central heating
In the case of central heating, the selection of the connection valves is very important. You can choose between using a manual valve or a valve with a thermostatic head.
Manual valve: the valve control head can be installed on the left/right side regardless of the hot water supply location. The temperatur eis controlled manually.
A valve with a thermostatic head: the integrated thermostat maintains the temperature inside the towel rail. The thermostatic head must be located at the hot water inlet (except MONO ONE).
The connection valves we offer are supplied with a clamping fitting for the most common pipes (Ø15 mm for copper and Ø16 mm for Alupex), so there is no need to buy anything else for the connection. For covering the inlet pipes and holes in the wall, we recommend the addition of cover rosettes.
Description
Radiator
Recommended connection sets: CORNER, CORNER COMBI, MONO ONE, COMPACT - see accessories
The heating rod is not part of the radiator. You will find the appropriate type in the accessories.
If the radiator is only electrically heated, it is necessary to purchase a ½ “plug for the radiator (see accessories).
Series description
Classical straight tube radiator with the possibility of a combination of central and electric heating
Combination of central and electric heating
Electrical heating
Central heating
Extended Warranty
Possibilities of "extreme" connection of heating ladders
1. Central heating - hand valve
CUBE Set COMPACT Set Copper Screw ALU Plug Covering Rope
If you decide to buy a ladder of this type, you need to choose a suitable attachment kit.
If the heating is to be used only for hot water heating without a thermostatic head, it is necessary to purchase a connection set
eg COMPACT or CUBE (according to heating design).
The CUBE is available in chrome, stainless steel or silver.
The COMPACT kit is available in chrome only. COMPACT and CUBE do not distinguish the right / left variant.
ADVICE! Tail pipe openings are not always perfectly executed, so we recommend that you purchase a set of cover rosettes. Covering rosettes serve to cover Cu or Alupex pipes and unclean openings in the wall. Covering rosettes are available in chrome or stainless steel.
ATTENTION! Our design valves have a special thread 24-19, so for each valve we have to buy the recommended clamping fittings according to the material and diameter of the pipe - copper / alupex.
Clamps are available in chrome or stainless steel.
2. Central heating - valve with thermostatic head
Set CORNER Copper fittings ALU fittings Covering rosettes
If you decide on a thermostatic variant, we recommend the CORNER version :
ADVICE! The CORNER is available in right / left version. The figure above shows the right option - the hot water supply is on the right, as well as the thermostat itself is located to the right (always in the front view). We recommend selecting the valve so that the head always points in the direction of the horizontal profiles of the heater, not on the opposite side (outside the heater). The triaxial design of the valve allows the valve head to be hidden beneath the radiator and thus does not occupy the space in the space.
The CORNER is available in chrome or stainless steel.
ATTENTION! The above-mentioned clamping fitting for heating assembling + cover rosette. Available color variation of chrome fitting or stainless steel. Covering rosettes are available in chrome or stainless steel.
3. Combined heating - valve with thermostatic head
Corner COMBI Heating rod Copper fittings ALU coupling Covering rosettes
If you decide to use the heater for both hot and electric heating, we recommend the CORNER COMBI connection set + heating rod:
ADVICE! The heating rod can be retrofitted, but this option is not recommended due to the probable need to dismantle the heating ladder and release the heating circuit. To select the heating rod, refer to variant 4.
ATTENTION! Again, it is necessary to select the right version of the left / right valve, see the above information.
The CORNER COMBI is available in chrome or stainless steel.
ATTENTION! Clamping screw + cover rosettes.
Available color variation of chrome fitting or stainless steel. Covering rosettes are available in chrome or stainless steel.
4. Electrical heating - with thermostatic heating rod
When choosing electric heating we offer a wide selection of heating rods - ONE, ONE-D, MOA, KTX, GV ...
ADVICE! The heating rod selects the client according to his own taste, design and performance!
ATTENTION! The heating rod must be of adequate power according to the specification of the heater or the closest lower possible.
If the heating is only electrically heated, it is necessary to fill the heater with an anti-corrosion freeze heat-resistant liquid. It is also necessary to purchase a ½ "plug for radiators.